FullTiltWiki

User Tools

Site Tools

Trace:
kb:projects:ftg:racing_simulator

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
kb:projects:ftg:racing_simulator [2025/01/26] – ↷ Page moved and renamed from kb:projects:montana_tech:senior_design to kb:projects:ftg:racing_simulator adminkb:projects:ftg:racing_simulator [2025/01/27] (current) – admin
Line 4: Line 4:
  
 We built his project in 2018 with as a group of three students. We designed the simulator together and then divided up the roles for the rest of the project. Heather wrote our reports and kept the administration off our backs so that we could work efficiently. Garon did all of the fabrication. I did the wiring and programming.  We built his project in 2018 with as a group of three students. We designed the simulator together and then divided up the roles for the rest of the project. Heather wrote our reports and kept the administration off our backs so that we could work efficiently. Garon did all of the fabrication. I did the wiring and programming. 
 +
 +The initial idea for this project came from Garon. He used to race outlaw carts, but a series of crashes and injuries made further racing unsafe. He wanted a way to get the thrill of racing without risking life and limb. I am still not convinced this is much safer, but it seemed like it would be when we started. The total power this platform is capable of putting out is more than the actual moving Baja Cart that another senior design team made.
  
 This is a project I have continued working on over the years. We have made several changes to improve the performance of the platform and make it more user friendly. We ended up doing a complete redesign and the second version is currently under development. This is a project I have continued working on over the years. We have made several changes to improve the performance of the platform and make it more user friendly. We ended up doing a complete redesign and the second version is currently under development.
 +
 +===== People =====
 +
 +  * Garon Knudson - Design, Fabrication, Crash Test Dummy
 +  * Heather Nelson - Design, Safety, Reports
 +  * [[people:robert_kuyper|Robert Kuyper]] - Design, Wiring, Programming/Integration
  
 ===== Versions ===== ===== Versions =====
Line 24: Line 32:
 ==== V1.1 ==== ==== V1.1 ====
  
-The year after our senior design, we allowed a second senior design team to modify our platform. This redesign only modified the upper platform. This modification increased the diameter to allow for greater range of motion. This upgrade almost doubled the motion envelope. Unfortunately, while I was driving during testing the Senior on the e-stop did not press it when a motor stopped running and we severely crashed the platform. This bent several heim joints, sheered a tooth of in one of our gearboxes, and fried the control board I had made. I quickly drew up a new board and we ordered a custom PCB to replace the fried board so we could limp through the end of the school year.+The year after our senior design, we allowed a second senior design team to modify our platform. This redesign only modified the upper platform which approximately doubled the range of motion. Unfortunately, while I was driving during testing the student on the e-stop did not press it when a motor stopped running and we severely crashed the platform. This bent several heim joints, sheered a tooth of in one of our gearboxes, and fried the control board I had made. I quickly drew up a new board and we ordered a custom PCB to replace the damaged board so we could limp through the end of the school year.
  
 ==== V1.2 ==== ==== V1.2 ====
  
-This was a repair to the V1.1 platform after our crash. Because the control board was burned out in the crash and we were running on a hasty replacement, we upgraded to an off the shelf controller with a lot more built in safety features. We also switched over from an Oculus Rift to a HTC Vive for our VR headset. This allowed us to implement motion compensation that subtracts the platform motion from the view movement. This helps keep the user from jumping out of the car and removes a lot of shake from the camera.+This was a repair to the V1.1 platform after our crash. Because the control board was burned out in the crash and we were running on a hasty replacement, we upgraded to an off the shelf controller with a lot more built in safety features. We also switched over from an Oculus Rift to a HTC Vive for our VR headset. This allowed us to implement motion compensation that subtracts the platform motion from the view movement. Motion compensation helps keep the user view from jumping out of the car and removes a lot of shake from the camera.
  
 ==== V2 ==== ==== V2 ====
Line 34: Line 42:
 Because of the relatively short period of time we had to settle on a design for the V1 platform, we made several compromises that limited the range of motion of the simulator. These limitations were due to pinch points in the control arms. The V1.1 platform helped alleviate some of collisions, but the original design was still fundamentally flawed.  Because of the relatively short period of time we had to settle on a design for the V1 platform, we made several compromises that limited the range of motion of the simulator. These limitations were due to pinch points in the control arms. The V1.1 platform helped alleviate some of collisions, but the original design was still fundamentally flawed. 
  
-The goal of this redesign was to re-use all of the electronics and arms from the V1.2 platform and replace the upper and lower frame to remove pinch points entirely. In order to get the most possible range of motion, custom heim joint spacers were designed to allow our rod ends to have more range of motion than anything currently available on the market. Without the pinch points, the range of motion is limited only by the length of the arms and the angular limitation of the heim joints. +The goal of this redesign was to re-use all of the electronics and arms from the V1.2 platform and replace the upper and lower frame to remove pinch points entirely. In order to get the most possible range of motion, custom heim joint spacers were designed to allow our rod ends to have more range of motion than anything currently available on the market. Without the pinch points, the range of motion is limited only by the length of the arms and the angular limitation of the heim joints. The final motion envelope will provide approximately 18 inches of heave, 12 inches of surge and sway, and 45 degrees of pitch, roll, and yaw. 
 + 
 +To improve safety, the ends of the arms are now captured by the frame. This prevents the arms from detaching completely from the platform if any of the bolts fail. To improve usability, the top platform is now easily removable to allow the cockpit to be use on or off of the platform. 
 + 
 +=== Status === 
 + 
 +The design is finalized. Garon is fabricating the new frame. The custom spacers have been sent out for manufacturing. I am moving all of the wiring into a new control box. 
 + 
 + 
 +===== Lessons Learned =====
  
-To improve safety, the ends of the arms are now captured by the frame. This prevents the arms from detaching completely from the platform if any of the bolts fail. To improve usability. The top platform is now easily removable to allow the cockpit to be use on or off of the platform.+  * Do not trust emergency equipment to people that do not understand the scope of the project and what failure modes look like. 
 +  * Create actionable safety documentation with explanations of failure modes and recovery procedures. 
 +  * Do not push untested code to hardware large enough to kill you without a reasonable exclusion zone. 
 +  * Place electronic components in a locations you can clearly see what you are touching.
kb/projects/ftg/racing_simulator.1737933058.txt.gz · Last modified: 2025/01/26 by admin

Page Tools

Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki